The Remora
HomeHome > News > The Remora

The Remora

May 28, 2023

In 2013 I got my first Polaroid camera, and since then I have been journeying into the world of instant film. From the inception of the Impossible Project to its recent merger, I eagerly followed the rediscovery of the formula for instant film, but was always frowning when I had to trash a battery.

When Rezivot's Power Ranger was launched, I discovered that I could hack together an external power source for SLR-type Polaroids. This took me on a journey into the Polaroid hacking world, and throughout this Winter of lockdown, I crafted my own solution for a rechargeable power source for my SLR670.

The journey into instant film photography was a bumpy one. The camera broke early on, the shop returned a different camera which was annoying since this one was a family gift. I had to chase them down to get the proper camera back, then find a new shop that would fix this one for me. The search didn't take long and we found another store with a more considerable owner, unfortunately the camera was beyond repair so by the following Easter I had another Polaroid SX-70 in my hands.

A year later, with fears of it breaking down, I decided to ship it to MiNT and have it upgraded to a SLR 670. This certainly made the results more consistent and as Impossible got better and better rediscovering the recipe for instant film, I became very satisfied with the photos I was producing. But, and there is always a but, the battery waste was something that always bugged me.

Here's what I cover:

The Analog community in Amsterdam has a member that spools Kodak Double X by hand and he was really excited for a high capacity film spooling solution announced by Rezivot (a brand unknown to me at the time). Sniffing around their social media, a product they were teasing in their Instagram feed got my attention. It was an external battery for SLR type polaroids. Finally a solution for this issue that had been bugging me all this time!

When they announced it my excitement dropped, the price tag was a bit steep, considering shipping and import taxes. Despite its bulkiness, the Power Ranger has a good design and a nice attention to detail. I particularly like the fact that it makes the camera stand straight on a horizontal surface.

A post shared by Rezivot (@rezivot)

One particular thing caught my attention, the Power Ranger has two contacts facing the camera. This got me intrigued — How the heck would they actually make contact with the camera? Little did I know that SX-70s have 2 contact test points under their belly. Hiding behind the skin, two holes on the bottom of the case open the way to a battery saving solution💡. This new found discovery took me on a journey into the Polaroid hacking community, only to find that it is quite active and full of ideas.

I began my search like most of them do nowadays, by hitting the search bar and typing all the search terms I could think of about polaroid battery hacks. Most of my searches kept hitting one domain in particular: — a blog/community/hack project by Joaquín de Prada. By hacking his way into the camera brains, Joaquín replaced the old board with a new PCB that uses Arduino based components to control the camera. His website is full of articles on how to hack the polaroids for many different things, such as converting an SX-70 to use 600 film, or how to leverage the contact holes under the camera. BINGO!!! This article, titled the i-Question, contained a substantial amount of solutions and hacks from other people. From using AA batteries to reusing Polaroid's own batteries or by building a small housing that looks similar to Rezivot's Power Ranger.

While I was digesting and brainstorming what I had encountered so far, Nico's Photography Show revealed another battery solution developed by an Instagram user by the alias helicord_camera, a camera hacker based in Hong Kong that designed a very elegant solution.

A post shared by Helicord TLR (@helicord_camera)

By extending the back of the camera he is able to make the necessary space to house whatever components he uses to make a battery unit. I was very tempted to get it, but decided not to. I have the silver version of the camera and this piece only comes in a muddy grey. However, there was a detail about this solution that teased me. This time it was the small size of the whole thing. Suddenly you didn't need 4 AA batteries or something as big as the power ranger. This showed me it was possible to create something small enough to power the camera, and like so, my search for a solution continued.

I cannot end this part without an honourable mention to another battery solution I found on Instagram from user johnny_inggg.

A post shared by Johnny_ing (@johnny_inggg)

I say honourable because I only found out about it while my project was already underway. It's a commercial solution very similar to the one from helicord_camera. So far, the most elegant that I have seen. Unfortunately it does not come in silver and the price tag is, once again, not very welcoming.

After reading through the article on, I got left with a doubt — how much power would I need to run the camera? The reason for this doubt originated from the fact that I saw some people using 4 AA batteries, which amounts to only 4.8 volts compared to 6 volts of the original batteries. There was some power tolerance here, but how much? I had to find out.

Having given all my electronic stuff away (mostly Arduino-based bits and pieces), I had to restock on components, so I headed off to a popular electronics website in the Netherlands. I was looking for things I thought I would need, such as switches, wires, buttons, LEDs, etc. In this search I stumbled upon something that caught my eyes, it was something called a power boost.

It's a little board that promises a 5v output with as little as a 1.8v input. I thought — This is exactly what I might need to make a powerful enough solution in a small package! Brilliant! — As it turns out, this would be exactly the thing, but more on that later.

After some research on all the possible booster boards the site had, I ended up getting one that had a charging circuit included. This would allow me to boost and charge the unit all in one piece, but with one constraint, I had to use LIPO batteries only. Because I was thinking of crafting a solution similar to johnny_inggg's one, a rectangular-shaped battery (typical format for LIPO) wouldn't be the thing I would initially go for, but this was only the first prototype, if it wouldn't work I could explore another path.

After analysing Polaroid's battery packs I saw that they have a 650mAh capacity. In the store the closest I could find was a 500mAh battery, which came in a nice compact size, not very far from the power boost board dimensions. I added to the cart some clamps and bread boards too and I was good to go for the first round of trialling. I was just missing one thing: a test subject!

In the second hand market I looked for another Polaroid, in working condition but not too pricey. The Dutch are very hard with this, they want full price for an untested camera, because a fully professionally serviced one costs 400 euros. After some weeks of bids and chats I eventually found one a bike ride away from home. Not in great shape on the outside, but perfectly working on the inside. Throw in an original manual, a carrying bag, neck strap and believe it or not, the original receipt and warranty card.

With all the components on my desk it was time to wire all the pieces together and try the powerboost out. First I did it with a LED, the Hello, World! of electronics. The light was on and with that my excitement built up. Next, it was the camera's turn.

The skin was in very poor condition, so I decided to get some mineral oil (aka white spirit in Netherlands) and a knife that would allow me to skin the whole thing. It's anyway a necessary step to access the bottom screws of the camera. This would better expose the contacts and allow me to have a look inside it, in order to gauge if I could perhaps put the components inside the camera itself.

A thing to note. Initially I was not aware of this, but Polaroid has its own proprietary screws!! You need to craft your own 1mm x 1mm square tool tip. That or get an overpriced one online. While you won't need that for my solution, it proved vital for me in order to open and investigate the camera.

With its guts out it was time to test the contact points, and bam! The camera worked like a charm! I was really happy with it, but conscious that this was just a first step.

With the electronics taken care of (for now) and after looking all around the guts of the camera I realized that I cannot fit anything inside it. On that, kudos to Polaroid for such a well designed compact camera, but for me it meant an outside solution. One that wouldn't be very invasive, in order to avoid damaging my main camera, and small enough not to get into the way of the camera's compactness, since I wanted to maintain this trait. It was time to get to the drawing board and start designing a 3D case that would house all the components.

To make the case I decided to dust off my OpenSCAD skills. I busted my caliper out and it was time to measure every single bit and component that I had.

By looking into different solutions (that can be found via Joaquin's article or by searching for the camera on thingiverse), I was trying to find inspiration on how to attach my case to the camera. Some people use clamps on the side and attach the whole unit to the underside of the camera.

Another solution is Rezivot's approach which leverages the tripod hole. I thought I could embed an Arca Swiss plate in my case design, this would then let me use the tripod hole too and still be able to mount the camera on a tripod. But in the back of my mind there was a voice telling me that this felt too bulky.

The first prototype consisted of only housings from the components, to make sure I had a solid and fitting case. Turns out this design was too tight, so I calculated some tolerances and moved things around to places that made more sense to me. I also introduced a lid for the case.

The second one worked well and it gave me an idea. If I increased the space inside the case, I could leverage the extra area to introduce magnets and attach the unit without using clamps or the tripod hole. Finally a compact enough solution that I felt really happy with! I proceeded to design some housing for the magnets and that resulted in the first working prototype of my solution.

Not learning from my initial mistake, I made the magnet fit too tight and I had to introduce some tolerances there too. Another issue that I encountered was measuring the actual highest component. I thought it was the battery, but it was a small component in the power boost board. After another round of adjustments, I got a second working prototype.

The Power boost board contains some useful LEDs that inform you of: power on, low battery, charging and fully charged. I wanted to be able to transport this information to the outside of the case. For this I got some small light pipes and tracing paper. With the help of some paper glue I was able to pinpoint the LEDs location with a fair degree of accuracy and with a small drill perforate the lid where I would install the light pipes.

The final step was to add some small cones around the contact pins. These cones help centring the pins in the holes under the camera.

The video below shows the fully assembled working prototype (charging)

With the main problem out of the way it was time to pay attention to the next challenge. Hacking the camera itself to accommodate for my design. Fortunately this was a simple enough task because it consists of just making 2 holes on the skin. To my surprise though, finding a template that would tell me where to make these holes was harder than I thought, in fact, impossible. There was no such resource available online. Just to find a template with the skin cuts proved itself quite tricky. I found only a couple of images, in a French forum, Tumblr and Flickr. Only the image on Tumblr had loose printing instructions — print in A4 — but had no margin information or if I should use 100%. This was bothersome because everything is closed at the moment and my printing attempts didn't match the camera dimensions. I am not going to the office, and don't have a printer at home, so I would have benefited from clear cut instructions on how to print this.

Because I couldn't wait, I used another bit of tracing paper to identify the holes. By using the tripod mount as the anchoring point and then marking the location of the holes, I made my own simple template. This worked out perfectly and my camera was now ready to use the prototype.

Since I could not find any information about where the contact holes are, I created a template for that purpose. It's meant to be printed in A4, comes with a 1:1 cutting template and the measurements diagram you see above. That way, if printing fails for some reason you still have a way to figure out where the holes are. Note that some Polaroid cameras have a metal sheet under the original skin, just peel a bit of the corner to find that out.

Ladies and Gentleman, I present you Remora-01:

I am very happy with the result. It's a compact, multifaceted solution. It's rechargeable and informative (by leveraging the LEDs on the board). It's easy to attach for anyone to use in their own cameras since it requires just some basic soldering and the creation of just two little holes on the Polaroid. This helps to preserve the camera's aesthetics and keeps the skin mostly intact, which ultimately were my 2 goals for this project.

I decided to name it Remora since the way I attach it to the camera reminded me of how remora fish attach themselves to other sea creatures.

The work is not done, but for now I will leave it as is. There are 2 other things I would like to do: one on the prototype itself and another on the spare camera that I got for this project.

While prototyping the case, I realized that the rugged nature of 3D prints provided enough friction for the lid to stay attached to the base. I thought of creating some screw mounts — I still intend to do so — but because of lockdown, I have no access to a couple of small screws whose size I can gauge and get in humble quantities.

For now I will trust the rugged grip between the parts.

After looking into the OpenSX70 project, I really liked the idea of it and I tried to get my hands on a board. Since I got the second working camera to prototype all of this, I thought it was a great chance to try and upgrade it to an OpenSX70. I have contacted the community and theoretically, since it's all open source, you can get the PCB design and order it, get the components and assemble the unit yourself and then burn in the software. Unfortunately I am not experienced enough to solder such small components, neither do I have the hardware to burn in the software, so for now, this is on hold until I can get my hands on a ready to go board.

This project was an entertaining time-killer for quarantine times. For now, I will leave you with all the necessary components, steps and resources (see below). Give it a go and feel free to reach out to me if you have any questions!

~ Nuno

The transfer of knowledge across the film photography community is the heart of EMULSIVE. You can add your support by contributing your thoughts, work, experiences and ideas to inspire the hundreds of thousands of people who read these pages each month. Check out the submission guide here.

If you like what you're reading you can also help this passion project by heading over to the EMULSIVE Patreon page and contributing as little as a dollar a month. There's also print and apparel over at Society 6, currently showcasing over two dozen t-shirt designs and over a dozen unique photographs available for purchase.

My name is Nuno Cruz, I was born in Portugal in a small northern city and now currently live in Amsterdam, The Netherlands. I studied computer science in Porto and it was during this time that my shutter bug was born.Little by little the bug grew bigger,... Click to see Nuno Cruz's full profile, links and other articles , and please make sure you also check out their website here.

BINGO!!! helicord_camera johnny_inggg. helicord_camera ~ Nuno Polaroid